トップページ - 製品 - OBD2コードスキャナ - ELM327 Plastic OBDII EOBD CANBUS Scanner V1.5 with 2102 Chip
« 戻る

ELM327 Plastic OBDII EOBD CANBUS Scanner V1.5 with 2102 Chip

商品番号 SC02-D
在庫あり
現価:1,030 円 
数量:
  
運送:
無料配送   郵便配送サービス 
配送時間:7-15営業日.詳細»
重量:
100g
規格:
22cm*15cm*2.5cm      ( Inch:8.66*5.91*0.98 )
返品:
7日以内に返品できますが、ただお客様は運賃を払います。詳細»
ELM327 Scanner can translate all the hard work of protocol into a simple ASCII character based view.Via the included serial cable, ELM327 V1.5 is used as an interface to connect virtually all OBD-II compliant vehicles to a PC for on-board diagnostics (OBD). Such vehicles are VW, Audi, Seat, Skoda, Opel, Vauxhall, Alfa, Mercedes, Smart, Renault, BMW, Peugeot, Citroen, Lotus, Ford, Rover, Aston Martin, Ferrari, etc.
ELM327 Plastic OBDII EOBD CANBUS Scanner V1.5 with 2102 Chip

Get Plastic USB ELM327 for 5 Reasons:


1. Supports 9 protocols in all - SAE J1850 PWM, SAE J1850 VPW, ISO 9141-2 and ISO 14230-4 as well as CAN Bus ISO 15765-4.
2. Internal EEPROM can remember the last protocol.
3. Precision-moulded diagnostic connector made to fit all VW/Audi vehicles, even those with "tight" trim around diagnostic socket.
4. ELM327 with USB port, software install easily.
5. Voltage input monitors your vehicle's battery.

USB ELM327 Technical Specification:

ELM327 Based - Datasheet
OBDII Plug: J1962 16-Pin Male (to Car)
USB Port : (to Computer or PDA)
High quality UL certified USB Cable (equivalent to CE).
CAN (ISO 15765-4)
SAE J1850 PWM
SAE J1850 VPW
ISO 9141-2
ISO 14230-4
Automatically searches for the correct protocol or can be configured manually.
USB Port
Serial Interface uses AT commands to look like a modem.
Status LED
Length with USB Lead : 1.5 metres

What's New for elm327:

RS232 baud rates to 500 Kbps
Adaptive Timing automatically adjusts ST timeouts
Power up to AT MA is selectable
Source (tester) address can be changed
Can reset all PPs with a jumper
Receive addresses can be independently set
Power Control with a low power standby mode
A 4800 baud ISO option
A non-volatile memory location for storing user data
CAN extended addressing support
You can now perform ISO/KWP bus initializations without having to send a request
An SS command allows searching through the OBD protocols sequentially
A new TA command allows the Tester Address to be easily changed
Factory calibration for the voltage reading circuit can be easily restored

J1850: 

Complete control over in frame responses (IFRs)
Delay before protocol 2 helps with some GM/Holden vehicles

ISO 9141 and ISO 14230: 

The slow initiation address can now be varied
Control over key word checking
KWP protocols can now transmit 3 or 4 byte headers

CAN: 

New J1939 protocol
Two user-definable CAN protocols
Improved error handling and recovery
Extended addressing support

How To Use USB ELM327:

1. Turn the car's ignition switch ON. No need to start the engine.
2. Start the software program, click "Options", select the correct communications port.
3. Your interface now works! Make sure the software can reliably access all the control modules that it should in your car.

Package including:

1pc x ELM327 Interface
1pc x CD Driver
スマホでQRコードをスキャンして、いつでも何処でも注文できる!

 
お問い合わせ
何か質問があれば、 お気軽にお知らせください。
Live Support:
オンラインチャット
E-Mail:sales@jobd2.jp
Skype:JOBD2.jp

ご注意ください:
製品を安全に送るために、電話番号が必要です。ご注文する時、電話番号を教えてください。
また、製品が無事に保証するため、パッケージに署名する前に、損傷があるかどうかを二重にチェックしてください。
もし、商品は損傷があれば、損傷を受けた証拠を開いてください。
Attention: please leave your telephone number for shipping arrival when you make payment for this product on our website.
レビューを書く
* 評価:
    レーティングを選択する。
* ラストネーム:
* お客様のE - Mailアドレス:
* 詳細を確認する:
本製品についての評価を教えて、経験を分かち合ってください。この製品だけに、意見を発表したことを確認してください。2日以内ですべての評価をに審査します。不適切な評価を削除する。
アフターサービスについて: Contact our Customer Service Department. (サービスの担当者はすぐに対応する。)
てください。ログイン first if you want to later edit or manage reviews uploaded by yourself.
Product's Tags:   ELM327
ブックマークに

JOBD2.jp

×