トップページ - 製品 - 自動車診断ツール - BMW EWS READER
« 戻る

BMW EWS READER

商品番号 SE39
在庫切れ
現価:11,500 円 
運送:
無料配送   郵便配送サービス 
配送時間:7-15営業日.詳細»
重量:
300g
返品:
7日以内に返品できますが、ただお客様は運賃を払います。詳細»
The Keymaker for EWS tool has been design for working with EWS alarm system. All BMW vehicles models equipped with EWS Immobilizers from 1995 year: E34(5xx), E36(3xx),E38 (7xx), E39 (5xx), E46 (3xx), E53 (X5), Z4, Mini Cooper, Rover 75, Range Rover.
Descriptions for BMW EWS Reader

Possibilities:

1. Work with all modifications of EWS1, EWS2, EWS3, EWS3+, EWS4
2. Reading and writing EWS3 and EWS3+ memory via unit connector (K-line).
(Don't ever try to read or write D47J mask processors! Those processors have active protection.)
3. Automatically detection of EWS version from EEprom memory.
4. Additional keys programming.
5. Used keys adding (if you know a password).
6. Used keys renew function (if you know a password).
7. Keys synchronization.
8. Activation and deactivation of available keys.
9. Coding of EWS.
10. EWS identification data changing (production date, EWS number etc.)
11. Used EWS3 resetting to factory conditions.
12. EWS VIN changing.
13. Key VIN change (after 1998).
14. EWS mileage changing (after 1998)
15. Key mileage changing (after 1998)

EWS's Motorola Processor masks checking.
Before reading the EWS processor check it's mask (see picture below)


Lector for ews display
Example of processor’s mask.

1. Old types of EWS1, EWS2 and EWS3 hw2 sw5 used the mask D47J. Take it off from EWS board and read with special adapter (in complete with EWS keymaker).
2. Use any programmer for reading of EWS4 and EWS4(1) processor.
3. New types of EWS3 and EWS3+ use the mask D46J. You can read it via EWS connector (K-line).

D47J mask processor’s adapter connection
Lector for ews display 2
K-line cable to EWS connection

Lector for ews display 3
EWS eeprom memory reading. "READ" button.

1. Disconnect and take off EWS module from a car.
2. Open it and take off an electronic board from EWS box.
3. Connect the device to your PC via USB cable. Install drivers from “USB_Driver"folder. If you work with D47J mask use adaptor, if it’s D46J use K-line cable.

Start the BMW EWS Reader software:
Lector for ews display 4
The software is ready to work via K-line cable at once. If you need to use D47J adapter change the operation mode:
Lector for ews display 5
Lector for ews display 6
Don't try to read 2D47J mask processor via K-line cable. It can damage processor internal memory.

Supply the power 12 Volt 500mA and over to the device. You have to connect power supply if you read EWS internal memory via it’s connector only. Then find
and clean the vanish on this point of EWS board:

Lector for ews display 7

Press the READ button. You will see the report at the bottom of the window
Lector for ews display 8
Touch the point mentioned above by the tester fixed to the device. You will see a progress report at the bottom of the window. You can remove the tester when reading process started. If you read 2D47J processor with adapter choose 2D47J and press READ button. After reading “OK"report will appear at the bottom of the window. Then press EDITOR bookmark at the top of the window.
Lector for ews display 9
EEprom memory file window will open
Lector for ews display 10
If there are 00 in all the lines it means that you forgot to connect external power supply while read the processor.

Then save this file on your hard disk with “File-Save as" command. You can save this file without reviewing if you press “File-Save as" bookmark on the top of the main window.

Lector for ews display 11
New EEprom memory writing. Open new file which you would like to write into the EWS
Lector for ews display 12
Press the Write button and touch the same point on the EWS board with the tester fixed to the device. If writing process has finished successfully you will see “OK" report on the bottom of the main window.
Lector for ews display 13
PCF7935 transponder and ELM key reading.
The Read/Write key bookmark.

Lector for ews display 14
The new window will open on the right
Lector for ews display 15
スマホでQRコードをスキャンして、いつでも何処でも注文できる!

 
お問い合わせ
何か質問があれば、 お気軽にお知らせください。
Live Support:
オンラインチャット
E-Mail:sales@jobd2.jp
Skype:JOBD2.jp

ご注意ください:
製品を安全に送るために、電話番号が必要です。ご注文する時、電話番号を教えてください。
また、製品が無事に保証するため、パッケージに署名する前に、損傷があるかどうかを二重にチェックしてください。
もし、商品は損傷があれば、損傷を受けた証拠を開いてください。
Attention: please leave your telephone number for shipping arrival when you make payment for this product on our website.
レビューを書く
* 評価:
    レーティングを選択する。
* ラストネーム:
* お客様のE - Mailアドレス:
* 詳細を確認する:
本製品についての評価を教えて、経験を分かち合ってください。この製品だけに、意見を発表したことを確認してください。2日以内ですべての評価をに審査します。不適切な評価を削除する。
アフターサービスについて: Contact our Customer Service Department. (サービスの担当者はすぐに対応する。)
てください。ログイン first if you want to later edit or manage reviews uploaded by yourself.
ブックマークに

JOBD2.jp

×