トップページ - 製品 - 自動車の診断ソフトウェア - ECU Flash Reprogramming for Toyota DVD
« 戻る

ECU Flash Reprogramming for Toyota DVD

商品番号 SS54
在庫あり
現価:3,300 円 
数量:
  
運送:
無料配送   郵便配送サービス 
配送時間:7-15営業日.詳細»
重量:
300g
返品:
7日以内に返品できますが、ただお客様は運賃を払います。詳細»
ECU Flash Reprogramming for Toyota DVD
IT IS POSSIBLE TO PERMANENTLY DAMAGE THE ECU (ECM/PCM) DURING THE FLASH REPROGRAMMING PROCESS.You must read and understand the following precautionary information before proceeding with reprogramming.

ECU Flash Reprogramming for Toyota DVD


IT IS POSSIBLE TO PERMANENTLY DAMAGE THE ECU (ECM/PCM) DURING THE FLASH REPROGRAMMING PROCESS.
You must read and understand the following precautionary information before proceeding with reprogramming.

You can minimize the risk of damaging an ECU by understanding the following precautions:

1. Battery must be fully charged and in good condition. BATTERY VOLTAGE MUST NOT FALL BELOW 11.4 VOLTS OR RISE ABOVE 16.0 VOLTS DURING THE REPROGRAMMING PROCESS.
2. All electrical accessories must be turned off and electrical loads must not be altered significantly during the reprogramming process (i.e. audio system, air conditioning system, interior lighting, daytime running lights, etc)
3. The engine compartment hood must be open and under hood ambient temperatures must not exceed 158ºF
4. Scantool/J2534 interface cables must be in good condition and connections must be electrically sound prior to beginning reprogramming (see TSB SS004-01, "ECU Flash Reprogramming Error Message" for more detail).
5. Do not disconnect the scantool, J2534 interface or PC during the reprogramming process; FAILURE TO FOLLOW THIS INSTRUCTION WILL RESULT IN PERMANENT DAMAGE TO THE ECU.
6. Do not allow the PC running J2534 Calibration Update Wizard software to go into standby or hibernation modes during the reprogramming process; FAILURE TO FOLLOW THIS INSTRUCTION WILL RESULT IN PERMANENT
DAMAGE TO THE ECU.
7. Do not cycle the ignition switch off during the reprogramming process except where instructed to do so by the Calibration Update Wizard or scantool software.
8. For ECUs that have more than one CPU to be reprogrammed, you must COMPLETE ALL CPUs before returning the vehicle to service.
9. To ensure stable battery voltage during this process, it is acceptable to connect a battery charger to the vehicle prior to beginning the reprogramming operation. Charger must be set on "low" charge rate and voltage must be maintained within the 11.4 volt to 16.0 volt window for the entire reprogramming process.
10. Set the parking brake for this operation

In addition to the above mentioned precautions, it is important to READ THE SPECIFIC TSB ASSOCIATED WITH THE REPROGRAMMING EVENT YOU ARE PERFORMING. Certain vehicles require removal of fuses to prevent accessories from energizing during the reprogramming process. FAILURE TO FOLLOW THE SPECIFIC DIRECTIONS IN THE APPLICABLE TSB FOR VEHICLE YOU ARE REPROGRAMMING CAN RESULT IN PERMANENT DAMAGE TO THE ECU.

View Getting-Started


Language: English
Quantity of CD: 1DVD
Date: 12.2009

スマホでQRコードをスキャンして、いつでも何処でも注文できる!

 
お問い合わせ
何か質問があれば、 お気軽にお知らせください。
Live Support:
オンラインチャット
E-Mail:sales@jobd2.jp
Skype:JOBD2.jp

ご注意ください:
製品を安全に送るために、電話番号が必要です。ご注文する時、電話番号を教えてください。
また、製品が無事に保証するため、パッケージに署名する前に、損傷があるかどうかを二重にチェックしてください。
もし、商品は損傷があれば、損傷を受けた証拠を開いてください。
Attention: please leave your telephone number for shipping arrival when you make payment for this product on our website.
レビューを書く
* 評価:
    レーティングを選択する。
* ラストネーム:
* お客様のE - Mailアドレス:
* 詳細を確認する:
本製品についての評価を教えて、経験を分かち合ってください。この製品だけに、意見を発表したことを確認してください。2日以内ですべての評価をに審査します。不適切な評価を削除する。
アフターサービスについて: Contact our Customer Service Department. (サービスの担当者はすぐに対応する。)
てください。ログイン first if you want to later edit or manage reviews uploaded by yourself.
ブックマークに

JOBD2.jp

×